Book

 

 

Each person has got their private assumption when it comes to How to Install a Bathtub Yourself.

Setting up a bathtub isn't specifically brain surgery, however it does require strong plumbing, woodworking, and occasionally, tiling abilities. Replacing an old tub with a new one is additionally a reasonably challenging task. If the old bathtub is readily easily accessible, the project can relocate rapidly; if you have to open up a wall to get rid of the old tub and also position the brand-new tub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will require a helper to vacate the old bathtub and embeded in the new one. See to it you have actually qualified on your own for the job and also are comfortable trying it. Instead of hiring a service provider to take over a halfway-completed job, it is better to think about using one before you begin. Opportunities are you may require a professional plumber to make tube links.
This article will assist you install a brand-new bathtub in your bathroom if you have actually already gotten a new bathtub and do not need to change the plan of your previous water supply pipelines.
Your tools as well as material list should comprise the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipeline Caps


 

Getting ready for the Installation

To start with, the supporting framework supplied with the bathroom should be fitted (if needed) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to ensure that if the faucet comes with a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet adapters to the bottom of the two taps using 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final position.

 

 

Removing Old Touches

If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is detach the supply of water. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the restricted access that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a towel prepared for the remaining water that will come from the pipelines. As soon as the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
Before carrying on to fit the brand-new taps, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.

 

 

Installing the Bath tub

Using both wooden boards under its feet, position the tub in the required placement. The wood boards are valuable in evenly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The following goal is to ensure that the bathtub is leveled all round. This can be accomplished by examining the level and also readjusting the feet on the bath tub till the level reviews degree.
To mount taps, fit the bottom of the furthest versatile faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the very same for the other tap.
Switch on the water system and inspect all joints and new pipework for leaks as well as tighten them if essential. Load the bathtub and likewise inspect the overflow outlet and the regular outlet for leaks.
Lastly, deal with the bathroom paneling as described in the producer's user's manual. Tiling and also securing around the bathtub should wait up until the bath tub has been utilized at the very least once as this will resolve it into its final placement.

 

 

Suitable New Touches

If the tails of the new faucets are plastic, then you will require a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the faucet in the placing hole in the bath/basin making sure that the washing machines are in location in between the faucet and the sink. Protect the faucet in place with the producer offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap adapters. The former kind should be linked to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.

 

 

Tiling Around the Bathtub

In the area where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to break an inflexible seal, causing the water to permeate the wall surface in between the bath as well as the tiling, resulting in issues with wetness and possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components and fittings. They are offered in tubes as well as cartridges, and also can sealing voids up to a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always fill up the bath tub with water prior to securing, to allow for the movement experienced when the tub is in use. The sealer can split rather very early if you do not take into account this activity before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly offered on the marketplace. It is a good idea to fit the tiles using waterproof or water-proof sticky as well as grout.

 

How to Install a Freestanding Bathtub?

 

Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.

This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.

 

Slope

 

Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.

 

Placement

 

A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.

According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.

 

Clean the bathroom floor

 

After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.

 

Steps to Install a Freestanding Bathtub:

 

STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.

STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.

STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.

STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.

STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.

STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.

 

Tips to Maintain a Freestanding Bathtub:

 

• Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter.


 
• Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches.


 
• Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains.


 
• Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris.


 
• Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run.


 
• If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.

 

https://www.magnushomeproducts.com/blogs/inspired-living/how-to-install-a-freestanding-bathtub-a-diy-method-with-6-steps

 

I hope you enjoyed reading our piece on How to Install a Bathtub Yourself. Thanks a ton for finding the time to read through our post. Are you aware of somebody who is fascinated about the topic? Please feel free to share it. I enjoy reading our article about Tools You Need to Install a New Bathtub .

Schedule Appointment